Axis Computer Networking Switches
The AXIS line of Computer Networking Switches includes a wide variety of features to meet your business's networking needs. This line includes managed switches, PoE+ devices, Soye, Unmanaged switches, and more. The AXIS managed switch features two SFP/RJ45 uplink ports and twenty-four PoE+ ports. This product also includes a 370W power supply and DCHP server for easy system configuration.
Unmanaged AXIS Computer Networking switches are typically used for small to medium networks with basic security needs. However, larger organizations with sensitive information on their network should invest in managed switches. These switches offer more security, features, and flexibility. They can be configured easily and may include data recovery solutions and redundancy procedures. However, they are typically more expensive.
While unmanaged switches require no special installation, they are often used improperly. Generally, these switches use auto-negotiation to determine the best data rate for your network. They can operate in either full or half-duplex mode. They also support SNMP.
When choosing a network switch, make sure to look for port counts and management capabilities. There are many different models and styles available, so don't just look at size. Ensure that you choose the right one for your specific IT needs. Consider whether you need a switch for home use or for a small business.
Managed AXIS Computer Networking Switches can save you money in the long run. They come with a single point of contact for support, and are ideally suited for small businesses with limited budgets. The switch is also designed for maximum redundancy. Its power management features support PoE class 3 and up to 60 W per port. You can even add more power by connecting midspans between ports. The managed AXIS computer networking switches have a five-year warranty.
Managed AXIS Computer Networking Switches come with extra security features. They provide network security and protection by detecting and containing threats. Managed switches can be managed by a networking team or administrator. They are cheaper and easier to use, but require more skill. Managed switches are generally more secure and provide greater redundancy.
To test whether AXIS Computer Networking Switches Support PoE+, first disconnect any Ethernet cable from the port and connect a known-good data only device to that port. Once connected, the device should be able to establish a data only Ethernet link and ping the switch VLAN SVI. Once connected, turn on the powered device. If the device does not power on, run the show inline power command to view the number of connected powered devices. It also gives you an indication of the switch power budget.
AXIS Computer Networking Switches with PoE+ support are ideal for surveillance applications. The T8516 PoE+ Network Switch has 16 PoE ports and a built-in DHCP server. It automatically discovers and supports up to 16 PoE cameras. Its GUI features a graphic topology and allows the network administrator to easily monitor all connected devices and their status.
Before a PoE connection can be established, the switch must detect and classify the PoE device. Once a device has been correctly classified, the PSE will assign PoE power to it. In an ideal scenario, the PD will report "power good" to the PSE after it has completed the process. If the PD does not report this, it will restart the PoE negotiation process. The failure of the PD to send the "power good" message can result in a device not being able to link up. It may also cause symptoms such as the device continually power cycling.
Cisco's PoE equipment supports five power classes and is designed to support each of them. Cisco PoE switches can adjust the power budget according to the IEEE classifications of powered devices.
When adjusting the MTU of AXIS Computer Networking Switches, you need to be careful not to set the MTU too high or too low. To ensure optimal performance, the MTU of an IP packet must be set as close as possible to the lowest MTU of the route. Fortunately, most devices can automatically adjust their MTU setting based on the type of network they are connected to.
Typically, MTUs are specified as a number of bytes smaller than the actual size of the packet being sent. Ethernet uses this number to limit the size of frames. The standard Ethernet protocol limits MTU to 1500 bytes. This means that if your AXIS Computer Networking Switches are set too high, your network will be constantly dropping frames due to over-sized frames.
The MTU setting on AXIS Computer Networking Switches should be set to 1500 bytes. This will prevent IP datagrams from being transmitted in jumbo Ethernet frames. However, it is important to note that MTU and MRU are not the same thing. While MTU and MRU are often used interchangeably, they have very different functions.
The MTU and BAG settings are critical for real-time applications. Both are a part of the configuration process. When the two are set to the same value, the switch will be able to maintain proper service levels, so your network is not affected in any way.
Soye AXIS computer networking switches are a great choice for small and mid-sized businesses. These inexpensive devices can be plugged into your network and start operating immediately. They are also referred to as unmanaged switches, since they do not need any configuration or monitoring.
Axis Computer Networking Switches have a cost-effective ownership model that includes a one-time purchase price and no ongoing service fees. They also provide 24/5 first-class support. They support PoE class 3, with up to 60 W per port. In addition, managed switches from Axis come with a 5-year warranty.
24/5 first-class support
AXIS Computer Networking Switches are backed by first-class support and 24/5 first-class technical support. They are designed for enterprise environments and hardened applications. These switches are easy to use and configure, and offer Power-over-Ethernet (PoE) options for high-power networks. They also feature flexible port counts of 4, 8, 16, 24 and 48 ports, and an Auto Power Reset feature.
Advanced traffic-handling features improve overall network performance. They prioritize delay-sensitive services, such as voice and video. They also identify network cabling faults and troubleshoot them. Another important feature is fast store-and-forward switching, which identifies and prevents damaged packets from passing through a network. They can also operate automatically, reducing user workload.
Enterprise Ethernet switches support Layer 2 networking and are designed to provide power to devices. They are equipped with Power-over-Ethernet (PoE) ports and fiber-optic backbones. They are available in managed and unmanaged models. They offer flexible VLAN configuration, as well as a variety of features and services to meet the needs of business users.
AXIS Computer Networking Switches offer 24/5 first-class support and are backed by a three-year warranty. AXIS is committed to offering the highest-quality products, and is proud to stand behind them. This support includes product knowledge and product training.